Can I Set Up a Tub Myself? Considerations As Well As Steps
Can I Set Up a Tub Myself? Considerations As Well As Steps
Blog Article
This great article down below on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is rather remarkable. You should give it a look.
Mounting a bathtub isn't specifically brain surgery, however it does need solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard job. If the old tub is readily available, the project can move speedily; if you have to open up a wall surface to get rid of the old bathtub as well as position the brand-new bath tub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the brand-new one. Make certain you have qualified yourself for the work and also are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is much better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you mount a new bath tub in your washroom if you have already acquired a brand-new tub and also do not need to change the setup of your previous water system pipes.
Your devices as well as material list must comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly come from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Using both wood boards under its feet, place the bathtub in the required setting. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub up until the spirit level reviews degree.
To set up faucets, fit all-time low of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Turn on the water system as well as check all joints and brand-new pipework for leakages and tighten them if necessary. Load the bath tub and also examine the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub must wait until the bath tub has been used at the very least once as this will resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap connectors. The previous type must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bath and also the tiling, resulting in difficulties with dampness as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always load the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can break relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking a few minutes to browse our piece of content. Enjoyed reading our review? Please share it. Help other people find it. Thank you for your time spent reading it.
Get An Estimate
Report this page